Skip to content

LUUM.IO

WALL SWITCH - INSTALL GUIDE#

Product Image

Introduction#

About This Guide#

This guide provides instructions for installing the SWITCH-B and SWITCH-W, Amatis wireless wall switches. In addition to the step-by-step installation process, this guide provides instructions on how to configure the wall switch, as well as some basic troubleshooting steps.

Product Overview#

The SWITCH-B and SWITCH-W are wireless wall switches, capable of controlling scenes. They connects to wireless networks via the Amatis Border Router (AMBR).

  • 24V wired or battery power options.
  • Surface and gang mount options.
  • Cloud connection via AMBR, uploading real-time data from your site to the Amatis config app.

Installation#

Parts List#

Before getting started with the installation process, it's important to make sure all the necessary components are included. Here's what should be found inside the box:

  • (1) Wall Switch
  • (2) Wall Box Screws (gang mount version only)

Placement#

Follow these guidelines when deciding on where to install the wall switch:

  • When using the surface mount switch, use double sided tape to secure it to a surface.

    Surface Mount

  • The gang mount switch is intended to be installed in an electrical box or wall box.

Gang Mount

  • The wall switch should be installed within 75' of an AMBR or other wireless node.

    Distance Limitations

    The Amatis system supports communication ranges up to 75' for wall switches with a clear line of site. Obstacles such as walls or floors will impact the communication ranges significantly.

Wiring#

The SWITCH-W has two wires for a low voltage 24V DC input. The SWITCH-B does not need to be connected to power, but the battery tabs need to be pulled.

Note

The input wires are polarity protected, either can be positive or negative.

Labeling & MAC Capture#

After installing any Amatis wireless device, it is imperative to note the device ID with the associated load/fixture/device. This is how the devices will be identified in the programmed. It is also a good idea to label any Amatis load controllers with the load they are controlling.

Note

The device ID can be found on the device’s packaging or the device itself.

Initial Setup#

Necessary Parts#

Review the following list to ensure all necessary parts are available:

  1. An active AMBR within communication range of the wall switch.
  2. Active power to the Switch6.
  3. Active power to the wall switch or the battery tabs pulled.

Device Configuration#

Perform the following steps to configure the device:

  1. Open up the Amatis App and navigate to the site.

  2. Open the Devices table and ensure a device with the ID noted in the previous step is active.

    Battery Switch

    When using a SWITCH-B, the device may need to be "awake" before it will show up in the Devices table. Instructions can be found below.

The device is now ready to be added to a location and programmed with the Amatis App.

Updating Firmware#

Perform the following steps to update the device's firmware:

  1. Open up the Amatis App and navigate to the site.
  2. Open the Devices table and find the device to be updated.

  3. Make sure the "Firmware Version" column is visible. If the firmware is out of date, it will show a yellow alert and yellow text.

    Battery Switch

    When using a SWITCH-B, the device will need to be "awake" in order to update the firmware. Instructions can be found below.

  4. Click on the out of date firmware to request a firmware update.

    firmware_update

    Note

    Depending on how out of date the firmware is, the programming may need to be synced to the devices after a firmware update.

Basic Troubleshooting#

Perform the following steps for basic troubleshooting of the device:

  1. Verify the device is operating normally using the LED Troubleshooting Matrix below.
  2. Verify the Switch6 has power by pressing the top or bottom button and confirming a green LED flashes in the top right corner of the switch.

LED Indicator Troubleshooting#

Use the following table to troubleshoot specific issues with the device based on the LED indicators:

LED Troubleshooting Matrix
LED Color SOLID FLASHING OFF
Green Factory reset in progress Three seconds: Startup

Single flash: Button press

Rapid flashing: Awake mode		 Normal Operation

No power if the LED is off when a button is pressed

Normal Operation

BOLD description indicates normal operation.

Button Operation#

The wall switch has a top and bottom button

Button Operation
ACTION BUTTON BEHAVIOR
1 Press Top Programmable scene
1 Press Bottom Programmable scene
5 Second Hold Top and Bottom Awake mode (SWITCH-B only)
10 Second Hold Top and Bottom Factory Reset

Technical Support#

If you experience any issues during installation or operation of this product, please contact our technical support team for assistance. Our technical support team is available via email at support@amatiscontrols.com. Please provide a detailed description of the issue you are experiencing, including any error messages or other relevant information.

Warranty#

All Amatis LED lighting products and controls come with a 5-year parts warranty, as well as labor per product up to a maximum of 50% of the material price for parts being replaced*. All parts are UL certified. Lamps are DLC certified, therefore eligible for utility incentives. We warrant that our products will be free from defects in material and workmanship for a 5-year period from the date of purchase. Defective products under warranty will be replaced with an equal or higher quality product.

Internet Connection

The Amatis Border Router (AMBR) connected to your affected device must have remained connected to the Amatis cloud via the Internet or cellular connection from the start of site commissioning to date of return request. Non-connected systems are eligible for a 2-year limited warranty (730 days) from shipment date, with the same remaining criteria.

Contacts#

Luum.io Headquarters
625 Kenmoor Ave STE 350
PMB 51933
Grand Rapids, MI. 49546
Phone: +1 (313) 314-3617

Document Feedback#

While we have taken great care to ensure the accuracy and completeness of this document, we welcome your feedback and suggestions to further improve it. If you notice any errors or omissions or feel that a topic could benefit from further explanation, please let us know by emailing your feedback to support@amatiscontrols.io. Your input is valuable to us and will help us enhance the quality and usefulness of our documentation.

Disclaimer#

All rights, title, and interest in and to this manual, including without limitation all copyright, trademark, patent, trade secret, and other proprietary rights, belong solely and exclusively to Luum.io and/or its licensors. This manual is provided solely for the purpose of assisting in the installation and operation of the device, and no license or other rights are granted or implied hereby. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of Luum.io. The contents of this manual are subject to change without notice. The information contained herein is provided on an 'as is' basis and is for informational purposes only. Luum.io makes no warranty, express or implied, as to the accuracy, completeness, or usefulness of this information, nor does it assume any legal liability or responsibility for the consequences of any errors or omissions therein. The names of actual companies and products mentioned herein may be the trademarks of their respective owners.